/* * Machine dependent startup code for SDP2430 boards. * Based on omap_start.S * * Copyright (c) 2002, 2003 Genetec Corporation. All rights reserved. * Written by Hiroyuki Bessho for Genetec Corporation. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. The name of Genetec Corporation may not be used to endorse or * promote products derived from this software without specific prior * written permission. * * THIS SOFTWARE IS PROVIDED BY GENETEC CORPORATION ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL GENETEC CORPORATION * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. * * Copyright (c) 2003 * Ichiro FUKUHARA . * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY ICHIRO FUKUHARA ``AS IS'' AND ANY EXPRESS OR * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. * IN NO EVENT SHALL ICHIRO FUKUHARA OR THE VOICES IN HIS HEAD BE LIABLE FOR * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * * Copyright (c) 2007 Microsoft * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. All advertising materials mentioning features or use of this software * must display the following acknowledgement: * This product includes software developed by Microsoft * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR IMPLIED * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. * IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTERS BE LIABLE FOR ANY DIRECT, * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. */ #include "opt_omap.h" #include "opt_com.h" #include #include #include "assym.h" #include #include RCSID("$NetBSD: sdp24xx_start.S,v 1.6 2011/06/30 20:09:28 wiz Exp $") #if 0 #define Invalidate_I_cache(reg) \ mcr p15, 0, reg, c7, c5, 0 /* Invalidate Entire I cache */ #else /* * Workaround Erratum 411920 * * - value of arg 'reg' Should Be Zero */ #define Invalidate_I_cache(reg) \ .p2align 5; \ mcr p15, 0, reg, c7, c5, 0; /* Invalidate Entire I cache */ \ mcr p15, 0, reg, c7, c5, 0; /* Invalidate Entire I cache */ \ mcr p15, 0, reg, c7, c5, 0; /* Invalidate Entire I cache */ \ mcr p15, 0, reg, c7, c5, 0; /* Invalidate Entire I cache */ \ nop; \ nop; \ nop; \ nop; \ nop; \ nop; \ nop; \ nop; \ nop; \ nop; \ nop; #endif /* * Kernel start routine for OMAP 1136 boards. * At this point, this code has been loaded into SDRAM * and the MMU is off */ .section .start,"ax",%progbits .global _C_LABEL(sdp2430_start) _C_LABEL(sdp2430_start): /* Move into supervisor mode and disable IRQs/FIQs. */ mrs r0, cpsr bic r0, r0, #PSR_MODE orr r0, r0, #(I32_bit | F32_bit | PSR_SVC32_MODE) msr cpsr, r0 /* * Set up a preliminary mapping in the MMU to allow us to run * at KERNEL_BASE with caches on. */ /* Build page table from scratch */ ldr r0, Ltemp_l1_table mov r1, r0 /* Save the page table address. */ /* Zero the entire table so all virtual addresses are invalid. */ mov r2, #L1_TABLE_SIZE /* in bytes */ mov r3, #0 mov r4, r3 mov r5, r3 mov r6, r3 mov r7, r3 mov r8, r3 mov r10, r3 mov r11, r3 1: stmia r1!, {r3-r8,r10-r11} stmia r1!, {r3-r8,r10-r11} stmia r1!, {r3-r8,r10-r11} stmia r1!, {r3-r8,r10-r11} subs r2, r2, #(4 * 4 * 8) /* bytes per loop */ bne 1b /* Now create our entries per the mmu_init_table. */ l1table .req r0 va .req r1 pa .req r2 n_sec .req r3 attr .req r4 itable .req r5 l1sfrm .req r6 adr itable, mmu_init_table ldr l1sfrm, Ll1_s_frame b 3f 2: str pa, [l1table, va] add va, va, #4 add pa, pa, #(L1_S_SIZE) adds n_sec, n_sec, #-1 bhi 2b 3: ldmia itable!, {va,pa,n_sec,attr} /* Convert va to l1 offset: va = 4 * (va >> L1_S_SHIFT) */ mov va, va, LSR #L1_S_SHIFT mov va, va, LSL #2 /* Convert pa to l1 entry: pa = (pa & L1_S_FRAME) | attr */ and pa, pa, l1sfrm orr pa, pa, attr cmp n_sec, #0 bne 2b .unreq va .unreq pa .unreq n_sec .unreq attr .unreq itable .unreq l1table .unreq l1sfrm /* * In theory, because the MMU is off, we shouldn't need all of this, * but let's not take any chances and do a typical sequence to set * the Translation Table Base. */ Invalidate_I_cache(r0) mcr p15, 0, r0, c7, c14, 0 /* Clean and Invalidate Entire Data Cache */ ldr r2, Lctl_ID_dis /* Disable I+D caches */ mrc p15, 0, r1, c1, c0, 0 /* " " " */ and r1, r1, r2 /* " " " */ mcr p15, 0, r1, c1, c0, 0 /* " " " */ #ifdef NOTYET /* * XXX Restrict cache size is reported to be unsupported on SDP2340 * XXX your CPU mileage may vary... as yet there is not generalized way to do this */ ldr r2, Lauxctl_CZ_restrict /* Restrict cache size */ mrc p15, 0, r1, c1, c0, 1 /* " " " */ orr r1, r1, r2 /* " " " */ mcr p15, 0, r1, c1, c0, 1 /* " " " */ #endif mcr p15, 0, r0, c7, c10, 4 /* Drain the write buffers. */ mcr p15, 0, r0, c2, c0, 0 /* Set Translation Table Base */ mcr p15, 0, r0, c8, c7, 0 /* Invalidate TLBs */ /* Set the Domain Access register. Very important! */ mov r0, #((DOMAIN_CLIENT << (PMAP_DOMAIN_KERNEL*2)) | DOMAIN_CLIENT) mcr p15, 0, r0, c3, c0, 0 /* * Enable the MMU, etc. */ mrc p15, 0, r0, c1, c0, 0 ldr r1, Lcontrol_wax and r0, r0, r1 ldr r1, Lcontrol_clr mvn r1, r1 and r0, r0, r1 ldr r1, Lcontrol_set orr r0, r0, r1 mcr p15, 0, r0, c1, c0, 0 /* * Ensure that the coprocessor has finished turning on the MMU. */ mrc p15, 0, r0, c2, c0, 0 /* Read an arbitrary value. */ mov r0, r0 /* Stall until read completes. */ /* * Jump to start in locore.S, which in turn will call initarm and main. */ b start /* Jump to start (flushes pipeline). */ nop nop nop nop /* NOTREACHED */ Ll1_s_frame: .word L1_S_FRAME Ltemp_l1_table: /* Put the temporary L1 translation table at the end of SDRAM. */ .word 0x80000000 + MEMSIZE * 0x100000 - L1_TABLE_SIZE /* * Coprocessor register initialization values */ # define CPU_AUXCTL_CZ (1 << 6) /* Restrict Cache Size */ /* bits to set in the Control Register */ Lcontrol_set: .word CPU_CONTROL_MMU_ENABLE | \ CPU_CONTROL_AFLT_ENABLE | \ CPU_CONTROL_DC_ENABLE | \ CPU_CONTROL_WBUF_ENABLE | \ CPU_CONTROL_32BP_ENABLE | \ CPU_CONTROL_32BD_ENABLE | \ CPU_CONTROL_LABT_ENABLE | \ CPU_CONTROL_SYST_ENABLE | \ CPU_CONTROL_IC_ENABLE /* bits to clear in the Control Register */ Lcontrol_clr: .word 0 /* bits to "write as existing" in the Control Register */ Lcontrol_wax: .word (3 << 30) | \ (1 << 29) | \ (1 << 28) | \ (3 << 26) | \ (3 << 19) | \ (1 << 17) /* bits to disable the caches */ Lctl_ID_dis: .word ~(CPU_CONTROL_IC_ENABLE|CPU_CONTROL_DC_ENABLE) /* bit to restrict cache size */ Lauxctl_CZ_restrict: .word CPU_AUXCTL_CZ /* We'll modify va and pa at run time so we can use relocatable addresses. */ #define MMU_INIT(va,pa,n_sec,attr) \ .word va ; \ .word pa ; \ .word n_sec ; \ .word attr ; mmu_init_table: /* Map KERNEL_BASE VA to SDRAM PA, write-back cacheable */ MMU_INIT(KERNEL_BASE, KERNEL_BASE, (MEMSIZE * L1_S_SIZE + L1_S_SIZE - 1) / L1_S_SIZE, L1_S_PROTO | L1_S_AP_KRW | L1_S_B | L1_S_C) /* Map first 1MB of L4 CORE (so console will work) */ MMU_INIT(OMAP2430_L4_CORE_VBASE, OMAP2430_L4_CORE_BASE, 1, L1_S_PROTO | L1_S_AP_KRW) /* Map first 1MB of L4 WAKEUP (so console will work) */ MMU_INIT(OMAP2430_L4_WAKEUP_VBASE, OMAP2430_L4_WAKEUP_BASE, 1, L1_S_PROTO | L1_S_AP_KRW) /* end of table */ MMU_INIT(0, 0, 0, 0)