$NetBSD: patch-ai,v 1.11 2015/08/21 11:03:44 is Exp $
- improve default configuration behavior for the modern world
- configure for pkgsrc
- DEVICE_GROUP is set from the pkgsrc makefile, so avoid compiler
  warnings by not defining it again when it's already set.
- honor PREFIX and VARBASE in paths
- turn on AUTO_PPP (whatever that is...?)

- no FLOW_HARD for fax-sending (for netbsd6)

--- policy.h.orig	2015-08-20 10:26:33.000000000 +0000
+++ policy.h
@@ -48,7 +48,12 @@
  * Normally, this is "/bin/login", just a few systems put "login"
  * elsewhere (e.g. Free/NetBSD in "/usr/bin/login").
  */
+#if defined(__NetBSD__) || defined(__FreeBSD__) ||\
+    defined(__OpenBSD__) || defined (__DragonFly__)
+#define DEFAULT_LOGIN_PROGRAM "/usr/bin/login"
+#else
 #define DEFAULT_LOGIN_PROGRAM "/bin/login"
+#endif
 
 /* FidoNet mailer support
  * 
@@ -86,7 +91,7 @@
  * If the path doesn't start with "/", it's relative to CONFDIR.
  */
 /* #define CNDFILE "dialin.config" */
-
+#define CNDFILE               "dialin.config"
 
 /* If you want to use /etc/gettydefs to set tty flags, define this
  * I recommend against it, I suspect some bugs lingering in that code
@@ -114,7 +119,9 @@
 /* group id that the device is chown()ed to. If not defined, the
  * primary group of "DEVICE_OWNER" is used.
  */
+#ifndef DEVICE_GROUP
 #define DEVICE_GROUP	"modem"
+#endif
 
 /* access mode for the line while getty has it - it should be accessible
  * by uucp / uucp, but not by others (imagine someone dialing into your
@@ -147,7 +154,9 @@
  *
  * if the directory does not exist, the log file goes to CONSOLE (!)
  */
-#define LOG_PATH "/var/log/mgetty.%s"
+#define STR1(x) #x
+#define STR(x) STR1(x)
+#define LOG_PATH STR(VARBASE) "/log/mgetty.%s"
 
 /* Default log error level threshold. Possible error levels are
  * L_FATAL, L_ERROR, L_AUDIT, L_WARN, L_MESG, L_NOISE, L_JUNK (see mgetty.h)
@@ -233,6 +242,7 @@
  */
 
 /* for a few systems, you can just take those defaults and be happy */
+/* pkgsrc note: these should *not* use VARBASE */
 #if defined (SVR4) || defined(sunos4)
 # define LOCK_PATH "/var/spool/locks"
 # define LOCK      "/var/spool/locks/LCK..%s"
@@ -439,7 +449,7 @@
  * that fax sending will time out after the first page sent (no ACK received)
  * and fail if FLOW_HARD is used. Use FLOW_SOFT instead.
  */
-#define FAXSEND_FLOW	FLOW_HARD | FLOW_SOFT
+#define FAXSEND_FLOW	FLOW_SOFT
  
 /* if your faxmodem switches port bit rate just after sending the "+FCON"
  * message to the host, define this to contain the baudrate used. (Not
@@ -459,7 +469,8 @@
  * watch out: if you run 'sendfax' as non-privileged user (user 'fax' etc.)
  * you might need to create this file manually and chown it to 'fax'
  */
-#define FAX_LOG		"/var/log/sendfax.log"
+/*#define FAX_LOG		"/var/log/sendfax.log" */ /* original */
+#define FAX_LOG         STR(VARBASE) "/spool/fax/Faxlog"
 
 /* local station ID (your fax number)
  * 20 character string, most faxmodem allow all ascii characters 32..127,
@@ -552,20 +563,15 @@
  */
 #ifdef SVR4
 # define MAILER		"/usr/bin/mailx -s 'Incoming facsimile message'"
-#else
-# if defined(_AIX) || defined(__NetBSD__) || defined(linux)
-#  define MAILER	"/usr/sbin/sendmail"
-#  define NEED_MAIL_HEADERS
-# endif
-# ifdef M_UNIX		/* SCO */
-#  define MAILER	"/usr/lib/mail/execmail"
-#  define NEED_MAIL_HEADERS
-# endif
-#endif
-
-#ifndef MAILER
+#elif defined(M_UNIX) /* SCO */
+# define MAILER		"/usr/lib/mail/execmail"
+# define NEED_MAIL_HEADERS
+#elif defined(__IRIX__)
 # define MAILER		"/usr/lib/sendmail"
 # define NEED_MAIL_HEADERS
+#else /* modern standard -- AIX, *BSD, Linux, etc. */
+# define MAILER		"/usr/sbin/sendmail"
+# define NEED_MAIL_HEADERS
 #endif
 
 /* where to send notify mail about incoming faxes to
@@ -586,13 +592,18 @@
  * If you don't want this type of service, do not define it at all
  * Absolute path name has to be used here!
  */
-#define FAX_NOTIFY_PROGRAM "/usr/local/lib/mgetty+sendfax/new_fax"
+#define FAX_NOTIFY_PROGRAM PREFIX "/lib/mgetty+sendfax/new_fax"
 
 /* default minimum space required on spooling partition for receiving a FAX
  * (in KILObytes)
  */
 #define	MINFREESPACE 1024
 
+
+#undef MGETTY_PID_FILE
+#define MGETTY_PID_FILE       "/var/run/mg-pid.%s"
+
+
 /* fax machines exchange so-called "non-standard-frames" that can be 
  * used to identify what vendor and model is on the other end.
  * mgetty parses and prints this by default, because it can help 
@@ -601,3 +612,4 @@
  */
 #define FAX_NSF_PARSER
 
+#define AUTO_PPP